path: root/lang/python+ipv6/files/Setup

# The file Setup is used by the makesetup script to construct the files
# Makefile and config.c, from Makefile.pre and config.c.in,
# respectively.  The file Setup itself is initially copied from
# Setup.in; once it exists it will not be overwritten, so you can edit
# Setup to your heart's content.  Note that Makefile.pre is created
# from Makefile.pre.in by the toplevel configure script.

# (VPATH notes: Setup and Makefile.pre are in the build directory, as
# are Makefile and config.c; the *.in files are in the source
# directory.)

# Each line in this file describes one or more optional modules.
# Comment out lines to suppress modules.
# Lines have the following structure:
#
# <module> ... [<sourcefile> ...] [<cpparg> ...] [<library> ...]
#
# <sourcefile> is anything ending in .c (.C, .cc, .c++ are C++ files)
# <cpparg> is anything starting with -I, -D, -U or -C
# <library> is anything ending in .a or beginning with -l or -L
# <module> is anything else but should be a valid Python
# identifier (letters, digits, underscores, beginning with non-digit)
#
# Lines can also have the form
#
# <name> = <value>
#
# which defines a Make variable definition inserted into Makefile.in
#
# Finally, if a line has the literal form
#
# *shared*
#
# (that is including the '*' and '*' !) then the following modules will
# not be included in the config.c file, nor in the list of objects to be
# added to the library archive, and their linker options won't be added 
# to the linker options, but rules to create their .o files and their
# shared libraries will still be added to the Makefile, and their
# names will be collected in the Make variable SHAREDMODS.  This is
# used to build modules as shared libraries.  (They must be installed
# using "make sharedinstall".)  (For compatibility, *noconfig* has the
# same effect as *shared*.)

# NOTE: As a standard policy, as many modules as can be supported by a
# platform should be present.  The distribution comes with all modules
# enabled that are supported by most platforms and don't require you
# to ftp sources from elsewhere.


# Some special rules to define PYTHONPATH.
# Edit the definitions below to indicate which options you are using.
# Don't add any whitespace or comments!

# Directories where library files get installed.
# DESTLIB is for Python modules; MACHDESTLIB for shared libraries.
DESTLIB=$(LIBDEST)
MACHDESTLIB=$(BINLIBDEST)

# NOTE: all the paths are now relative to the prefix that is computed
# at run time!

# Standard path -- don't edit.
# No leading colon since this is the first entry
# Empty since this is now just the runtime prefix.
DESTPATH=

# Site specific path insertions -- should begin with : if non-empty
SITEPATH=

# Standard enabled (tests are always available)
TESTPATH=:test

# Path for machine- or system-dependent modules (and shared libraries)
MACHDEPPATH=:plat-$(MACHDEP)

COREPYTHONPATH=$(DESTPATH)$(SITEPATH)$(TESTPATH)$(MACHDEPPATH)$(STDWINPATH)$(TKPATH)
PYTHONPATH=$(COREPYTHONPATH)


# The modules listed here can't be built as shared libraries for
# various reasons; therefore they are listed here instead of in the
# normal order.

# Some modules that are normally always on:

regex regexmodule.c regexpr.c   # Regular expressions, GNU Emacs style
pcre pcremodule.c pypcre.c  # Regular expressions, Perl style (for re.py)
posix posixmodule.c     # posix (UNIX) system calls
signal signalmodule.c       # signal(2)

# The SGI specific GL module:

#gl glmodule.c -lgl -lX11   # Graphics Library -- SGI only

# The thread module is now automatically enabled, see Setup.thread.

# Pure module.  Cannot be linked dynamically.
# -DWITH_QUANTIFY, -DWITH_PURIFY, or -DWITH_ALL_PURE
#WHICH_PURE_PRODUCTS=-DWITH_ALL_PURE
#PURE_INCLS=-I/usr/local/include
#PURE_STUBLIBS=-L/usr/local/lib -lpurify_stubs -lquantify_stubs
#pure puremodule.c $(WHICH_PURE_PRODUCTS) $(PURE_INCLS) $(PURE_STUBLIBS)

# Uncommenting the following line tells makesetup that all following
# modules are to be built as shared libraries (see above for more
# detail):

#*shared*


# GNU readline.  Unlike previous Python incarnations, GNU readline is
# now incorporated in an optional module, configured in the Setup file
# instead of by a configure script switch.  You may have to insert a
# -L option pointing to the directory where libreadline.* lives,
# and you may have to change -ltermcap to -ltermlib or perhaps remove
# it, depending on your system -- see the GNU readline instructions.
# It's okay for this to be a shared library, too.

readline readline.c -lreadline -ltermcap


# Modules that should always be present (non UNIX dependent):

array arraymodule.c # array objects
cmath cmathmodule.c # complex math library functions
math mathmodule.c -lm   # math library functions, e.g. sin()
strop stropmodule.c # fast string operations implemented in C
struct structmodule.c   # binary structure packing/unpacking
time timemodule.c # -lm # time operations and variables
operator operator.c # operator.add() and similar goodies

_locale _localemodule.c  # access to ISO C locale support


# Modules with some UNIX dependencies -- on by default:
# (If you have a really backward UNIX, select and socket may not be
# supported...)

fcntl fcntlmodule.c # fcntl(2) and ioctl(2)
pwd pwdmodule.c     # pwd(3) 
grp grpmodule.c     # grp(3)
select selectmodule.c   # select(2); not on ancient System V
socket socketmodule.c   # socket(2); not on ancient System V
errno errnomodule.c # posix (UNIX) errno values

# The crypt module is now disabled by default because it breaks builds
# on many systems (where -lcrypt is needed), e.g. Linux (I believe).
crypt cryptmodule.c -lcrypt # crypt(3); needs -lcrypt on some systems

*shared*

# Some more UNIX dependent modules -- off by default, since these
# are not supported by all UNIX systems:

nis nismodule.c     # Sun yellow pages -- not everywhere
termios termios.c   # Steen Lumholt's termios module
resource resource.c # Jeremy Hylton's rlimit interface


# Multimedia modules -- off by default.
# These don't work for 64-bit platforms!!!
# These represent audio samples or images as strings:

audioop audioop.c   # Operations on audio samples
imageop imageop.c   # Operations on images
rgbimg rgbimgmodule.c   # Read SGI RGB image files (but coded portably)


# The stdwin module provides a simple, portable (between X11 and Mac)
# windowing interface.  You need to ftp the STDWIN library, e.g. from
# ftp://ftp.cwi.nl/pub/stdwin.  (If you get it elsewhere, be sure to
# get version 1.0 or higher!)  The STDWIN variable must point to the
# STDWIN toplevel directory.

# Uncomment and edit as needed:
#STDWIN=/ufs/guido/src/stdwin

# Uncomment these lines:
#STDWINPATH=:$(DESTLIB)/stdwin
#LIBTEXTEDIT=$(STDWIN)/$(MACHDEP)/Packs/textedit/libtextedit.a
#LIBX11STDWIN=$(STDWIN)/$(MACHDEP)/Ports/x11/libstdwin.a
#stdwin stdwinmodule.c -I$(STDWIN)/H $(LIBTEXTEDIT) $(LIBX11STDWIN) -lX11

# Use this instead of the last two lines above for alphanumeric stdwin:
#LIBALFASTDWIN=$(STDWIN)/$(MACHDEP)/Ports/alfa/libstdwin.a
#stdwin stdwinmodule.c -I$(STDWIN)/H $(LIBTEXTEDIT) $(LIBALFASTDWIN) -ltermcap


# The md5 module implements the RSA Data Security, Inc. MD5
# Message-Digest Algorithm, described in RFC 1321.  The necessary files
# md5c.c and md5.h are included here.

md5 md5module.c md5c.c


# The mpz module interfaces to the GNU Multiple Precision library.
# You need to ftp the GNU MP library.  
# The GMP variable must point to the GMP source directory.
# This was originally written and tested against GMP 1.2 and 1.3.2.
# It has been modified by Rob Hooft to work with 2.0.2 as well, but I
# haven't tested it recently.

# A compatible MP library unencombered by the GPL also exists.  It was
# posted to comp.sources.misc in volume 40 and is widely available from
# FTP archive sites. One URL for it is:
# ftp://gatekeeper.dec.com/.b/usenet/comp.sources.misc/volume40/fgmp/part01.Z

#GMP=/ufs/guido/src/gmp
#mpz mpzmodule.c -lgmp


# SGI IRIX specific modules -- off by default.

# These module work on any SGI machine:

# *** gl must be enabled higher up in this file ***
#fm fmmodule.c -lfm -lgl        # Font Manager
#sgi sgimodule.c            # sgi.nap() and a few more

# This module requires the header file
# /usr/people/4Dgifts/iristools/include/izoom.h:

#imgfile imgfile.c -limage -lgutil -lm  # Image Processing Utilities


# These modules require the Multimedia Development Option (I think):

#al almodule.c -laudio          # Audio Library
#cd cdmodule.c -lcdaudio -lds -lmediad  # CD Audio Library
#cl clmodule.c -lcl -lawareaudio    # Compression Library
#sv svmodule.c yuvconvert.c -lsvideo -lXext -lX11   # Starter Video


# The FORMS library, by Mark Overmars, implements user interface
# components such as dialogs and buttons using SGI's GL and FM
# libraries.  You must ftp the FORMS library separately from
# ftp://ftp.cs.ruu.nl/pub/SGI/FORMS.  It was tested with FORMS 2.2a.
# The FORMS variable must point to the FORMS subdirectory of the forms
# toplevel directory:

#FORMS=/ufs/guido/src/forms/FORMS
#fl flmodule.c -I$(FORMS) $(FORMS)/libforms.a -lfm -lgl


# SunOS specific modules -- off by default:

#sunaudiodev sunaudiodev.c


# George Neville-Neil's timing module:

timing timingmodule.c


# The _tkinter module.
#
# The TKPATH variable is always enabled, to save you the effort.
TKPATH=:lib-tk

# The command for _tkinter is long and site specific.  Please
# uncomment and/or edit those parts as indicated.  If you don't have a
# specific extension (e.g. Tix or BLT), leave the corresponding line
# commented out.  (Leave the trailing backslashes in!  If you
# experience strange errors, you may want to join all uncommented
# lines and remove the backslashes -- the backslash interpretation is
# done by the shell's "read" command and it may not be implemented on
# every system.

# *** Always uncomment this (leave the leading underscore in!):
# _tkinter _tkinter.c tkappinit.c -DWITH_APPINIT \
# *** Uncommend and edit to reflect where your X11 header files are:
#   -I/usr/X11R6/include \
# *** Or uncomment this for Solaris:
#   -I/usr/openwin/include \
# *** Uncomment and edit to reflect where your Tcl/Tk headers are:
#   -I/usr/local/include \
# *** Uncomment and edit for Tix extension only:
#   -DWITH_TIX -ltix4.1.8.0 \
# *** Uncomment and edit for BLT extension only:
#   -DWITH_BLT -I/usr/local/blt/blt8.0-unoff/include -lBLT8.0 \
# *** Uncomment and edit for PIL (TkImaging) extension only:
#   -DWITH_PIL -I../Extensions/Imaging/libImaging  tkImaging.c \
# *** Uncomment and edit for Mesa (what's Mesa?):
#   -lGL -lGLU -lMesatk -lMesaaux \
# *** Uncomment and edit for TOGL extension only:
#   -DWITH_TOGL togl.c \
# *** Uncomment and edit to reflect where your Tcl/Tk libraries are:
#   -L/usr/local/lib \
# *** Uncomment and edit to reflect your Tcl/Tk versions:
#   -ltk8.0 -ltcl8.0 \
# *** Uncomment and edit to reflect where your X11 libraries are:
#   -L/usr/X11R6/lib \
# *** Or uncomment this for Solaris:
#   -L/usr/openwin/lib \
# *** Always uncomment this; X11 libraries to link with:
#   -lX11 -lXext -lXmu


# Lance Ellinghaus's modules:

rotor rotormodule.c     # enigma-inspired encryption
syslog syslogmodule.c       # syslog daemon interface


# Lance's curses module.  This requires the System V version of
# curses, sometimes known as ncurses (e.g. on Linux, link with
# -lncurses instead of -lcurses; on SunOS 4.1.3, insert -I/usr/5include
# -L/usr/5lib before -lcurses).

curses cursesmodule.c -lncurses -ltermcap



# Tommy Burnette's 'new' module (creates new empty objects of certain kinds):

#new newmodule.c


# Generic (SunOS / SVR4) dynamic loading module.
# This is not needed for dynamic loading of Python modules --
# it is a highly experimental and dangerous device for calling
# *arbitrary* C functions in *arbitrary* shared libraries:

dl dlmodule.c

# Modules that provide persistent dictionary-like semantics.  You will
# probably want to arrange for at least one of them to be available on
# your machine, though none are defined by default because of library
# dependencies.  The Python module anydbm.py provides an
# implementation independent wrapper for these; dumbdbm.py provides
# similar functionality (but slower of course) implemented in Python.

# The standard Unix dbm module:

dbm dbmmodule.c     # dbm(3) may require -lndbm or similar

# Anthony Baxter's gdbm module (derived from Jack's dbm module)
# GNU dbm(3) will require -lgdbm:

#gdbm gdbmmodule.c -I/usr/local/include -L/usr/local/lib -lgdbm


# Berkeley DB interface.
#
# This requires the Berkeley DB code, see
# ftp://ftp.cs.berkeley.edu/pub/4bsd/db.1.85.tar.gz
#
# Edit the variables DB and DBPORT to point to the db top directory
# and the subdirectory of PORT where you built it.

#DB=/depot/sundry/src/db.1.85/
#DBPORT=$(DB)/PORT/sunos.5.2
#bsddb bsddbmodule.o -I$(DB)/include -I$(DBPORT) $(DBPORT)/libdb.a
bsddb bsddbmodule.o



# David Wayne Williams' soundex module
#soundex soundex.c

# Helper module for various ascii-encoders
binascii binascii.c

# Fred Drake's interface to the Python parser.
#parser parsermodule.c

# Digital Creations' cStringIO and cPickle
cStringIO cStringIO.c
cPickle cPickle.c


# Lee Busby's SIGFPE modules.
# The library to link fpectl with is platform specific.
# Choose *one* of the options below for fpectl:

# For SGI IRIX (tested on 5.3):
#fpectl fpectlmodule.c -lfpe

# For Solaris with SunPro compiler (tested on Solaris 2.5 with SunPro C 4.2):
# (Without the compiler you don't have -lsunmath.)
#fpectl fpectlmodule.c -R/opt/SUNWspro/lib -lsunmath -lm

# For other systems: see instructions in fpectlmodule.c.
fpectl fpectlmodule.c

# Test module for fpectl.  No extra libraries needed.
fpetest fpetestmodule.c

# Andrew Kuchling's zlib module.
# This require zlib 1.0.4 (or later).  See http://quest.jpl.nasa.gov/zlib/
zlib zlibmodule.c -lz


# Example -- included for reference only:
# xx xxmodule.c